This topic has been archived. It cannot be replied.
-
枫下家园 / 我爱我车 / 换雪胎,有一个轮子怎么也下不来。螺丝都下了。用过的方法有:脚踹。后备胎敲。松了螺丝上路开一段。急刹车。还是不行。有没有同志有经验的?谢谢!!!
-zgzdr( 找工作的人);
2016-11-13
(#10421937@0)
-
勇敢!
-beachineseman(不容易啊);
2016-11-13
(#10421942@0)
+5
-
以前扭得太紧了,所以diy的人需要买一个torque wrench.
-hunhunhunhun(不知道);
2016-11-13
(#10421959@0)
-
以前一直是店里搞的,这次排队时间太长,所以自己搞。店里都是用高压气动的搞的,拆下来的螺丝帽好几个都裂了
-zgzdr( 找工作的人);
2016-11-13
(#10421974@0)
-
店里一般设定在90左右的torque,也不会有大问题。关键是锈,螺丝帽是涨裂的。你的不会是toyota吧?
-torontospy(Spy);
2016-11-13
(#10422010@0)
+1
-
这个肯定不止。拧下来的时候,一片烟雾缭绕
-zgzdr( 找工作的人);
2016-11-14
(#10422132@0)
-
外面,除了costco, 我就没见过用torque wrench的。
-m1wm1w(临江仙);
2016-11-14
(#10423269@0)
-
Taylor tire @ Warden/Denison就是用torque wrench。今年两次换轮胎都是在他家。经理是个大美女。
-bennyxyz(Ben);
2016-11-14
(#10423335@0)
-
无它,腿劲不够耳。
-madog(武疯子);
2016-11-13
(#10421968@0)
+1
-
您是说继续踹?
-zgzdr( 找工作的人);
2016-11-13
(#10421971@0)
-
车行的人一般用一根4x4用力敲,几下就掉下来。
-madog(武疯子);
2016-11-14
(#10422204@0)
-
去店里吧,跟我的一个车一样,我还惨点儿,想换roter+pad, 可是有2个螺丝弄不下来,是位置太别扭,且没升降机。碰巧也是一轮胎下部来,就换break rotor 时一起弄了。
-torontospy(Spy);
2016-11-13
(#10422001@0)
-
店里要排队
-zgzdr( 找工作的人);
2016-11-14
(#10422131@0)
-
总比下不来强吧?没准儿蛮力过大把哪里损坏了就更坏了,而且你花的时间比等的还多。锈得那么死,劝你别自己折腾了。
-torontospy(Spy);
2016-11-14
(#10422240@0)
-
继续轮胎砸,两边轮流砸
-benbenli(大岭);
2016-11-13
(#10422012@0)
-
砸了100多下,没有用
-zgzdr( 找工作的人);
2016-11-14
(#10422128@0)
-
喷油了没,penetration oil
-mtlu2(poker face);
2016-11-13
(#10422116@0)
-
喷了wd40. 关键里面的地方喷不到啊
-zgzdr( 找工作的人);
2016-11-14
(#10422129@0)
-
只能往缝里喷了点。
-zgzdr( 找工作的人);
2016-11-14
(#10422130@0)
-
好像不能用wd40. 店里一般给轴承处抹银灰色的东西,而且不抹螺丝处. 好像以前没处理好.
-fedora(fedora);
2016-11-14
(#10422172@0)
-
喷油是这次卸胎的,银灰色的叫ANTI-SEIZE, 再装上去用的
-mtlu2(poker face);
2016-11-14
(#10423989@0)
-
顺便请教一下,涂ANTI-SEIZE之前如何清洁轴承处?可以用WD-40喷吗?还是用什么刷子?
-dongji(冬季阳光);
2016-11-14
(#10424878@0)
-
啥也不需要,喷在刹车盘上就危险了。
-hunhunhunhun(不知道);
2016-11-16
(#10428663@0)
-
刹车盘上不能喷吗?不是说可以用WD-40清洗刹车盘除锈吗?
-dongji(冬季阳光);
2016-11-16
(#10429532@0)
-
后备胎比较軽, 最好用另外一个正常轮胎去敲,要敲在车上轮子的边上,轮子转90度,再敲
-canadagoose(楓中秋雁);
2016-11-14
(#10422170@0)
-
用大铁锤,从里向外敲,要敲在轮胎上,不能砸铁圈上
-fedora(fedora);
2016-11-14
(#10422176@0)
-
大铁锤,会把轮胎钢丝打弯。
-hunhunhunhun(不知道);
2016-11-14
(#10424184@0)
-
原因是店里没在轮毂和hub接触处抹anti-size 或 grease, 然后又over-torque hub nuts
-canadagoose(楓中秋雁);
2016-11-14
(#10422173@0)
-
居然有这种事情,头一次听说
-kking(捣蛋);
2016-11-14
(#10422205@0)
-
估计从来没做过 ROTATION。
-troyd(•);
2016-11-14
(#10422212@0)
-
估计是开了几年头一次拆
-kking(捣蛋);
2016-11-14
(#10423323@0)
-
Puller--2爪或3爪的都行。
-go2caa(walleye桂花鱼);
2016-11-14
(#10424059@0)
+1
-
这个怎么用?没有地方顶啊。是铝合金轮子
-zgzdr( 找工作的人);
2016-11-15
(#10426536@0)
-
顶着轴心,然后拉出来。
-go2caa(walleye桂花鱼);
2016-11-15
(#10426644@0)
-
看看这个。
-troyd(•);
2016-11-14
(#10422209@0)
+1
-
谢谢!
-zgzdr( 找工作的人);
2016-11-15
(#10426535@0)
-
我就是松开螺帽1豪米,开出去,最好转圈。最长一次开了2公里;最后肯定能开松。
-chli(不闲);
2016-11-14
(#10424375@0)
-
嗯,今天晚上最后试一次,不行就送车行了
-zgzdr( 找工作的人);
2016-11-15
(#10426534@0)
-
我家哥昨天也碰到同样情况,最后还是硬砸下来的,结论是还是要有力气,不过代价是一只皮鞋弄坏了,不知他砸轮廓为啥会把皮鞋弄坏?你要不找个力气大的朋友或邻居试试?
-mocarly(放下);
2016-11-15
(#10426551@0)
-
大力金刚脚踹的呗
-walkthrough(老花镜);
2016-11-16
(#10427521@0)
-
这,安全吗?轮子会不会飞出去?
-mocarly(放下);
2016-11-15
(#10426540@0)
-
有5个螺丝,哪不安全?绝对放心。这招比那些砸的馊主意强多了。一旦松了,离螺丝掉下来至少还有几十公里。
我干过俩回(第二回是尽管抹了Anti-seize,还是又锈住了)。
-chli(不闲);
2016-11-15
(#10427038@0)
-
我也遇到过。我当时是把螺丝卸下来,慢慢放千斤顶,用车的重量把轮子弄松。
-aaronding(流浪的八毛儿);
2016-11-15
(#10426637@0)
-
这招儿值得一试,最好只松几扣,带着螺帽放。
-37101(出城下乡);
2016-11-15
(#10426978@0)
-
不知道你搞定了没有。如果还没有,参考一下这段录像对于初次动手的人很有帮助。加拿大风格的。
-bj6395(bj6395);
2016-11-15
(#10427236@0)
-
为省几十块钱, 冒着一切危险和几天的时间值得吗?
-guanshui88(约定);
2016-11-15
(#10427286@0)
-
告诉你我的经验,先把螺丝上回去但不上紧,留一点空隙。然后把车放低,让轮胎回到地面,最好把千斤顶放低不受力。然后人用力横向晃动车体(跟轮胎表面垂直的方向用力)。晃几次,然后再把车升起来,应该就行了。
-winterfish(潜水鱼(\ (•◡•) /));
2016-11-15
(#10427427@0)
-
我试过以下两种方法,1,螺丝松动后放下jack, 用车重使RIM脱离。 2. 用两个Jack双保险后钻到彻底脸朝上躺着往外踹。 3. 站在轮胎旁用脚踹。第三种最吃力,有一个轮胎踹了50脚才成功,腿肚子痛
-walkthrough(老花镜);
2016-11-16
(#10427522@0)
-
明年不自己干了,感觉不值得,万一把骨头肌肉踹出问题了就不值得了。
-walkthrough(老花镜);
2016-11-16
(#10427523@0)
-
2就是在找死啊
-m1wm1w(临江仙);
2016-11-16
(#10428200@0)
+3
-
话歪理不歪!这样干太危险了, 用脚在里边踹,车一动千金顶跑了怎么办!
-atlantic2003(sydney);
2016-11-16
(#10428259@0)
-
我的轮毂锈死了,送去车行,拿一铁棍撬,一下就开了。
-rits(老军医);
2016-11-16
(#10428156@0)
-
找一个长一点的2*4或4*4木头,(比车宽度长),轮子架起来一点点,从另一边拿锤子敲
-thickroad(四环胡同);
2016-11-16
(#10428692@0)
-
终于换了雪胎了。楼上的各种办法都试了。都不行。今天到了店里,店里小伙子一开始用小锤子敲。后来换了个大铁锤,双手用的那种,敲了好几下,敲下来了。当时在旁边看,心惊胆战,就怕他敲坏什么东西。下来以后,装雪胎之前,也没有涂什么东西,用电刷子刷了下,就上了轮胎。回来我自己又卸下来,涂了油。完毕
-zgzdr( 找工作的人);
2016-11-23
{226}
(#10442771@0)
-
谢谢update,良心楼主
-callsunday(喜欢过周末);
2016-11-23
(#10443013@0)
-
现在想来,即使有大铁锤,你也做不了。不把车架高,大铁锤也使不上劲啊。
-zgzdr( 找工作的人);
2016-11-23
(#10443418@0)
-
老松说的办法你一定没有试。
-hnryll(松树);
2016-11-23
(#10444491@0)
-
说说看呢
-zgzdr( 找工作的人);
2016-11-24
(#10445339@0)